Fabrication Of A Standard Waeel Barrow

FABRICATION OF A STANDARD WAEEL BARROW

ABSTRACT

The project is about fabrication of wheel barrow which is fabricated in mechanical Engineering workshop in institute of management and technology, Enugu.

The report comprise five chapters, chapter one is about the introduction (background of the study) of the wheel-barrow, chapter tow is about the literature review, chapter three is about the theory and analysis of problem, chapter four is about Assembling of the wheel barrow, chapter five is about conclusion, recommendation and references 

 

 

 

 

 

 

 

 

 

TABLE OF CONTENT

Cover page

Title page

Letter of transmittal

Release page

Approval page

Dedication

Acknowledgment

Abstract

Table of content

Chapter one

Introduction

Background of the study

Aim/objective

Scope and limitation

Chapter two

Literature review

Common features of wheel-barrow,

Function of wheel barrow,

Specification of problems

Synthesis of solution

Chapter three

Theory and analysis of problem

Material selection and analysis,

Reasons for material selection,

Strength of material

Construction/fabrication procedure

Beaning analysis

Chapter four

Assembling of the wheel-barrow

Testing and evaluation of the machine

Cost analysis

Reliability

Performance

Durability

Chapter five

Conclusion and recommendation

Cocnlsuion

Recommendation

Diagram of wheel-Barrow (sections)

Assembling drawing (all the section parts)

Reference

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RELEASE NOTE

Having accomplished the fabrication of the absolute utilization of the machine by the department. For any purpose they may want to use it. This project could be reproduced, reconstructed, modernized and cold be re-fabricated with the order from the department. There is no embargo on the written of machines piracy. We here by release the project (the fabrication of a standard wheel barrow) to the department of mechanical Engineering in institute of management and technology Enugu

 

 

 

 

 

 

 

 

 

 

Letter of transmittal

Department of Mechanical

Engineering, School of Engineering

Institute of Management and Technology

05^th December, 2013

The Head of Department

Department of Mechanical Engineering

Schools of Engineering

 

Dear Sir,

       SUBMISSION OF PROJECT REPORT

Having successfully completed the fabrication of a standard wheel berrow under the supervision of Mis. Adiele of mechanical Engineering Department of the Institute of management and technology (imt) Enugu.

I wish to submit the report to the departmental board for consideration in accordance with the rules and regulation for the award of National Diploma (ND).

                                                        Yours Faithfully                                     

                                                        Nwabuzor Desmond L.              

CHAPTER ONE

INTRODUCTION

1.1     Background of the Study

It is often said that man are born free back are always in Chain, in one way or the other, human beings are faced with a lot of problem. there was a time when it is difficult to carry a load from one place to anthem but as time goes one, solutions where prefer to this problem by providing a simple machine called wheelbarrow to help transport goods form one place to another.

A wheelbarrow is a small hand propelled vehicle usually with just one wheel, designed to be pushed and guided by a single person using two handles to the rear or by a sail to push the ancient wheelbarrow by wind. The machine has two hands where efforts are applied, it also has a portion where loads are loaded. The fulcrum takes change of it movement and so many other features. This machine is fabricated to relieve the difficulties and probably eliminate loss of man-power time, money and especially the need for technological  break through self reliance.           

1.2       AIM OBJECTIVES

The aim of fabricating this wheel barrow is as follows

1.          To know how to fabricate a slandered wheel barrow.

2.          To eradicate the problems faced by human’s in carrying goods form one place to another.

3.          To lessen difficulties and probably eliminate lost of man-power

4.          To identify how wheel barrow can be assistance in the society.    

1.3     SCOPE AND LIMITATION

SCOPE

       This study/work is designed to cover the construction or fabrication of a standard wheelbarrow.

LIMITATION

It is a difficult task to cover the fabrication of all simple machinery is Nigeria. The producer concentrated in the fabrication of wheelbarrow. During the fabrication, the producer also faced the following constantans.

a.                          Time: The time ell acted to this work is short compared to the production of the wheelbarrow.

b.                          Financial constraint: Financial is another problem faced by the producer during the constriction. There is no enough fund for the producer.